{"id":472835653659,"title":"AEM Electronics - Water\/Methanol Failsafe Device - SAE 1\/4\" Fittings","handle":"aem-electronics-water-methanol-failsafe-device-sae-1-4-fittings-30-3020","description":"\u003cstrong\u003eSpecifications:\u003c\/strong\u003e\u003cbr\u003eManufacturer: AEM Electronics\u003cbr\u003ePart Number: 30-3020\u003cbr\u003eAEM’s Water\/Methanol FAILSAFE Device is the most advanced water\/methanol failsafe device on the market. It actively monitors the injection system’s ENTIRE flow curve to compensate for failure under ANY condition, allowing you to use your water\/methanol system with complete peace of mind. If you have a water\/methanol injection system or are considering one, you will not find a more advanced failsafe device on the market than the AEM Water\/Methanol FAILSAFE Device.\u003cbr\u003e\u003cbr\u003e Can be used on virtually all water\/methanol injection systems with either ¼” or 4mm OD tubing\u003cbr\u003e PC programmable with “Auto Set” feature that automatically creates baseline configuration\u003cbr\u003e Built-in warning lights inform user of an alarm trigger\u003cbr\u003e\u003cbr\u003e Tunable PC-based software with USB connectivity\u003cbr\u003e One low-side (ground) driver and one high-side (+12V) driver can be configured to turn on or off during an alarm condition\u003cbr\u003e Fully adjustable alarm delay and reset period\u003cbr\u003e 0-5v Analog output for use with data loggers and virtually all engine management systems\u003cbr\u003e Auxiliary input for use with AEM Water\/Methanol \"Boost Safe\" feature can trigger an alarm event if there is a system readiness issue (open circuit, short circuit, low fluid level, etc.)\u003cbr\u003e Precision flow sensor included\u003cbr\u003e Data analysis using AEMdata software.\u003cbr\u003e Today’s water\/methanol injection systems have proven themselves as a viable means for effectively reducing engine inlet air temperatures and suppressing harmful detonation. This allows enthusiasts to reliably increase boost and advance ignition timing without the need for racing fuel. Despite the proven effectiveness and reliability of water\/methanol injection, there exists a potential for engine damage if the water\/methanol tank runs dry, if the pump stops working or more commonly if flow volume decreases due to fuel contamination, a clogged nozzle or a leak in the system.\u003cbr\u003e \u003cbr\u003e While failsafe devices for water\/methanol are not new, competitors’ failsafe systems have limitations that do not allow them to completely protect your engine if the water\/methanol injection system stops flowing. Most failsafe devices have settings for high and low range flow parameters, but only monitor flow at a single point. And, without actually calculating volume versus time to establish a flow rate, instead running the system at full blast and using the nozzle’s potential for flow as your established flow rate, it is impossible to know the actual flow of the water\/methanol system. Short version: if you think you are flowing 500cc\/min and are actually flowing 300cc\/min, and you are relying on your failsafe to trigger an alarm at a single reference point using 500cc\/min of flow as your reference, then you have created the potential for engine damage.\u003cbr\u003e \u003cbr\u003e Other competitors’ failsafe systems use a flow meter to establish water\/methanol flow and utilize an external adjustment to trigger an alarm if the system does not detect maximum flow, using a time-delay strategy to compensate for part throttle operation. The problem is, water\/methanol flow is rarely zero or maximum flow, and with all of the potential flow rates one can experience, a time delay strategy is not completely failsafe.\u003cbr\u003e \u003cbr\u003e Actively monitors the entire water\/methanol fuel injection curve to trigger an alarm event under any defined adverse condition!\u003cbr\u003e Can be used on virtually all water\/methanol injection systems with either 1\/4\" or 4mm OD tubing\u003cbr\u003e \"Auto Set\" feature automatically creates baseline configuration\u003cbr\u003e Built-in warning lights inform user of an alarm trigger\u003cbr\u003e Internal data logger records all injection flow and alarm status data\u003cbr\u003e Included high-tech analog gauge has black and white faceplates and bezels to match vehicle interior, and is programmable for either 0-500cc\/min or 0-1000cc\/min flow ranges\u003cbr\u003e Gauge alarm and backlighting are user programmable to match interior lighting\u003cbr\u003e Data analysis using AEMdata software.\u003c!--split--\u003e\u003cstrong\u003eTaxes:\u003c\/strong\u003e\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eSingapore and Malaysia: \u003c\/strong\u003eAll import taxes are included in our pricing.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eEuropean Tva, Iva: \u003c\/strong\u003eTaxes will be calculated during checkout at our company import rate. No additional charges will be added by your local authority.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eUSA:\u003c\/strong\u003e If this product is shipped from our US warehouse then taxes are included. Otherwise, please refer to the rest of the world paragragh.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eRest of the World:\u003c\/strong\u003e Other countries may have to pay their local import tax depending on your country's regulations.\n\u003chr\u003e\n\u003cstrong\u003eShipping: \u003c\/strong\u003e\u003cbr\u003e\u003cbr\u003eThis product will be shipped from our US Warehouse to any global location. Shipping via DHL within 3 to 7 days depending on location and local custom check. Allow two additional days for order processing.\u003cbr\u003eEvery Monday our team keeps you in the loop by sending out an \"estimated time of arrival\" email.\u003c!--split--\u003e\u003c!--split--\u003eThe RZCrew team listed this item for its performance and trusted reliability.\u003cbr\u003eReliable coilovers are important for your safety, don't settle for cheap parts that fail. Buy original!","published_at":"2017-12-23T06:45:45-12:00","created_at":"2017-12-23T06:45:46-12:00","vendor":"AEM Electronics","type":"Display - Gauges - Sensors","tags":["aem-electronics","aem-electronics24","analog","display-gauges-sensors","gauges-gauges","gc-white","methanol-flow","standalone-gauge","tva","Universal"],"price":28800,"price_min":28800,"price_max":28800,"available":true,"price_varies":false,"compare_at_price":28800,"compare_at_price_min":28800,"compare_at_price_max":28800,"compare_at_price_varies":false,"variants":[{"id":5442355789851,"title":"Default Title","option1":"Default Title","option2":null,"option3":null,"sku":"30-3020","requires_shipping":true,"taxable":true,"featured_image":null,"available":true,"name":"AEM Electronics - Water\/Methanol Failsafe Device - SAE 1\/4\" Fittings","public_title":null,"options":["Default Title"],"price":28800,"weight":5500,"compare_at_price":28800,"inventory_quantity":42,"inventory_management":"shopify","inventory_policy":"deny","barcode":""}],"images":["\/\/cdn.shopify.com\/s\/files\/1\/2343\/5009\/products\/30-3020.jpg?v=1514054746"],"featured_image":"\/\/cdn.shopify.com\/s\/files\/1\/2343\/5009\/products\/30-3020.jpg?v=1514054746","options":["Title"],"content":"\u003cstrong\u003eSpecifications:\u003c\/strong\u003e\u003cbr\u003eManufacturer: AEM Electronics\u003cbr\u003ePart Number: 30-3020\u003cbr\u003eAEM’s Water\/Methanol FAILSAFE Device is the most advanced water\/methanol failsafe device on the market. It actively monitors the injection system’s ENTIRE flow curve to compensate for failure under ANY condition, allowing you to use your water\/methanol system with complete peace of mind. If you have a water\/methanol injection system or are considering one, you will not find a more advanced failsafe device on the market than the AEM Water\/Methanol FAILSAFE Device.\u003cbr\u003e\u003cbr\u003e Can be used on virtually all water\/methanol injection systems with either ¼” or 4mm OD tubing\u003cbr\u003e PC programmable with “Auto Set” feature that automatically creates baseline configuration\u003cbr\u003e Built-in warning lights inform user of an alarm trigger\u003cbr\u003e\u003cbr\u003e Tunable PC-based software with USB connectivity\u003cbr\u003e One low-side (ground) driver and one high-side (+12V) driver can be configured to turn on or off during an alarm condition\u003cbr\u003e Fully adjustable alarm delay and reset period\u003cbr\u003e 0-5v Analog output for use with data loggers and virtually all engine management systems\u003cbr\u003e Auxiliary input for use with AEM Water\/Methanol \"Boost Safe\" feature can trigger an alarm event if there is a system readiness issue (open circuit, short circuit, low fluid level, etc.)\u003cbr\u003e Precision flow sensor included\u003cbr\u003e Data analysis using AEMdata software.\u003cbr\u003e Today’s water\/methanol injection systems have proven themselves as a viable means for effectively reducing engine inlet air temperatures and suppressing harmful detonation. This allows enthusiasts to reliably increase boost and advance ignition timing without the need for racing fuel. Despite the proven effectiveness and reliability of water\/methanol injection, there exists a potential for engine damage if the water\/methanol tank runs dry, if the pump stops working or more commonly if flow volume decreases due to fuel contamination, a clogged nozzle or a leak in the system.\u003cbr\u003e \u003cbr\u003e While failsafe devices for water\/methanol are not new, competitors’ failsafe systems have limitations that do not allow them to completely protect your engine if the water\/methanol injection system stops flowing. Most failsafe devices have settings for high and low range flow parameters, but only monitor flow at a single point. And, without actually calculating volume versus time to establish a flow rate, instead running the system at full blast and using the nozzle’s potential for flow as your established flow rate, it is impossible to know the actual flow of the water\/methanol system. Short version: if you think you are flowing 500cc\/min and are actually flowing 300cc\/min, and you are relying on your failsafe to trigger an alarm at a single reference point using 500cc\/min of flow as your reference, then you have created the potential for engine damage.\u003cbr\u003e \u003cbr\u003e Other competitors’ failsafe systems use a flow meter to establish water\/methanol flow and utilize an external adjustment to trigger an alarm if the system does not detect maximum flow, using a time-delay strategy to compensate for part throttle operation. The problem is, water\/methanol flow is rarely zero or maximum flow, and with all of the potential flow rates one can experience, a time delay strategy is not completely failsafe.\u003cbr\u003e \u003cbr\u003e Actively monitors the entire water\/methanol fuel injection curve to trigger an alarm event under any defined adverse condition!\u003cbr\u003e Can be used on virtually all water\/methanol injection systems with either 1\/4\" or 4mm OD tubing\u003cbr\u003e \"Auto Set\" feature automatically creates baseline configuration\u003cbr\u003e Built-in warning lights inform user of an alarm trigger\u003cbr\u003e Internal data logger records all injection flow and alarm status data\u003cbr\u003e Included high-tech analog gauge has black and white faceplates and bezels to match vehicle interior, and is programmable for either 0-500cc\/min or 0-1000cc\/min flow ranges\u003cbr\u003e Gauge alarm and backlighting are user programmable to match interior lighting\u003cbr\u003e Data analysis using AEMdata software.\u003c!--split--\u003e\u003cstrong\u003eTaxes:\u003c\/strong\u003e\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eSingapore and Malaysia: \u003c\/strong\u003eAll import taxes are included in our pricing.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eEuropean Tva, Iva: \u003c\/strong\u003eTaxes will be calculated during checkout at our company import rate. No additional charges will be added by your local authority.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eUSA:\u003c\/strong\u003e If this product is shipped from our US warehouse then taxes are included. Otherwise, please refer to the rest of the world paragragh.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eRest of the World:\u003c\/strong\u003e Other countries may have to pay their local import tax depending on your country's regulations.\n\u003chr\u003e\n\u003cstrong\u003eShipping: \u003c\/strong\u003e\u003cbr\u003e\u003cbr\u003eThis product will be shipped from our US Warehouse to any global location. Shipping via DHL within 3 to 7 days depending on location and local custom check. Allow two additional days for order processing.\u003cbr\u003eEvery Monday our team keeps you in the loop by sending out an \"estimated time of arrival\" email.\u003c!--split--\u003e\u003c!--split--\u003eThe RZCrew team listed this item for its performance and trusted reliability.\u003cbr\u003eReliable coilovers are important for your safety, don't settle for cheap parts that fail. Buy original!"}

AEM Electronics - Water/Methanol Failsafe Device - SAE 1/4" Fittings

Check products, lead time and fitting infos in the tabs below!
Sku: 30-3020
Availability: 5 to 10 days Lead Time.
Shipping time is additional.
USD 288.00
Maximum quantity available reached.
Specifications:
Manufacturer: AEM Electronics
Part Number: 30-3020
AEM’s Water/Methanol FAILSAFE Device is the most advanced water/methanol failsafe device on the market. It actively monitors the injection system’s ENTIRE flow curve to compensate for failure under ANY condition, allowing you to use your water/methanol system with complete peace of mind. If you have a water/methanol injection system or are considering one, you will not find a more advanced failsafe device on the market than the AEM Water/Methanol FAILSAFE Device.

Can be used on virtually all water/methanol injection systems with either ¼” or 4mm OD tubing
PC programmable with “Auto Set” feature that automatically creates baseline configuration
Built-in warning lights inform user of an alarm trigger

Tunable PC-based software with USB connectivity
One low-side (ground) driver and one high-side (+12V) driver can be configured to turn on or off during an alarm condition
Fully adjustable alarm delay and reset period
0-5v Analog output for use with data loggers and virtually all engine management systems
Auxiliary input for use with AEM Water/Methanol "Boost Safe" feature can trigger an alarm event if there is a system readiness issue (open circuit, short circuit, low fluid level, etc.)
Precision flow sensor included
Data analysis using AEMdata software.
Today’s water/methanol injection systems have proven themselves as a viable means for effectively reducing engine inlet air temperatures and suppressing harmful detonation. This allows enthusiasts to reliably increase boost and advance ignition timing without the need for racing fuel. Despite the proven effectiveness and reliability of water/methanol injection, there exists a potential for engine damage if the water/methanol tank runs dry, if the pump stops working or more commonly if flow volume decreases due to fuel contamination, a clogged nozzle or a leak in the system.

While failsafe devices for water/methanol are not new, competitors’ failsafe systems have limitations that do not allow them to completely protect your engine if the water/methanol injection system stops flowing. Most failsafe devices have settings for high and low range flow parameters, but only monitor flow at a single point. And, without actually calculating volume versus time to establish a flow rate, instead running the system at full blast and using the nozzle’s potential for flow as your established flow rate, it is impossible to know the actual flow of the water/methanol system. Short version: if you think you are flowing 500cc/min and are actually flowing 300cc/min, and you are relying on your failsafe to trigger an alarm at a single reference point using 500cc/min of flow as your reference, then you have created the potential for engine damage.

Other competitors’ failsafe systems use a flow meter to establish water/methanol flow and utilize an external adjustment to trigger an alarm if the system does not detect maximum flow, using a time-delay strategy to compensate for part throttle operation. The problem is, water/methanol flow is rarely zero or maximum flow, and with all of the potential flow rates one can experience, a time delay strategy is not completely failsafe.

Actively monitors the entire water/methanol fuel injection curve to trigger an alarm event under any defined adverse condition!
Can be used on virtually all water/methanol injection systems with either 1/4" or 4mm OD tubing
"Auto Set" feature automatically creates baseline configuration
Built-in warning lights inform user of an alarm trigger
Internal data logger records all injection flow and alarm status data
Included high-tech analog gauge has black and white faceplates and bezels to match vehicle interior, and is programmable for either 0-500cc/min or 0-1000cc/min flow ranges
Gauge alarm and backlighting are user programmable to match interior lighting
Data analysis using AEMdata software.
Taxes:

Singapore and Malaysia: All import taxes are included in our pricing.

European Tva, Iva: Taxes will be calculated during checkout at our company import rate. No additional charges will be added by your local authority.

USA: If this product is shipped from our US warehouse then taxes are included. Otherwise, please refer to the rest of the world paragragh.

Rest of the World: Other countries may have to pay their local import tax depending on your country's regulations.
Shipping:

This product will be shipped from our US Warehouse to any global location. Shipping via DHL within 3 to 7 days depending on location and local custom check. Allow two additional days for order processing.
Every Monday our team keeps you in the loop by sending out an "estimated time of arrival" email.
The RZCrew team listed this item for its performance and trusted reliability.
Reliable coilovers are important for your safety, don't settle for cheap parts that fail. Buy original!