Fuel Rail

{"id":7155352502454,"title":"Radium Engineering Nissan Silvia SR20DET Fuel Rail Kit - S13","handle":"radium-engineering-nissan-silvia-sr20det-fuel-rail-kit-s13-20-0558","description":"\u003cstrong\u003eSpecifications:\u003c\/strong\u003e\u003cbr\u003eManufacturer: Radium Engineering\u003cbr\u003eReference Number: 20-0558\u003cbr\u003e\u003cbr\u003e\u003cbr\u003e\u003cbr\u003eThis CNC machined fuel rail for the Nissan SR20DET features a large 0.69 inch internal bore and high flow ports that accept a wide variety of adapter fittings to suit any custom installation. The black satin anodized finish makes it safe to use with all blends of gasoline and alcohol fuels. It installs to the factory fuel rail mounting points and uses aftermarket top-feed fuel injectors.This fuel rail features an extra 8AN ORB port in the center on the bottom. This can be used as a location for a Radium FPD-R fuel pulse damper (P\/N 20-0176), as shown below. Fuel pulse dampers can be found HERE. Or this port can be plugged.\nThis fuel rail kit is designed for the Nissan S13 SR20DET (RWD configuration) intake manifold.This S13 SR20DET fuel rail will also work on most aftermarket intake manifolds that use the OEM fuel rail (as shown below).\u003cbr\u003e\u003cbr\u003e\nNOTE: there are many aftermarket intake manifolds available for the SR20DET. Radium Engineering has not tested every manifold on the market. Please use the photos on this page to judge if the fuel rail may be compatible. And always ask the intake manifold producer if the OEM fuel rail is compatible. If so, then the Radium fuel rail will likely work as well.Lastly, 3 of the plastic OEM 5mm spacers (Nissan 17522-10V00) must be reused and placed under the included mounting brackets for thermal insulation and proper fuel rail height.The Radium fuel rail converts from side feed fuel injectors to top feed, allowing the use of high flow aftermarket fuel injectors. Fuel injectors are not included and not sold by Radium Engineering. Reference the diagram below to ensure compatible fuel injectors are obtained. For this fuel rail, a 34mm tall universal injector with 14mm upper and lower O-rings must be used. Most popular injector suppliers offer a fuel injector in this configuration. Refer the injector supplier to this page if needed.\nNOTE: Short 34mm injectors are used in this kit because hood clearance may become an issue if taller injectors are used.\u003cbr\u003e\nThe billet aluminum injector seats are anodized and laser etched and press into the intake manifold as shown. They provide a sealed base for the top feed injectors.\u003cbr\u003e\u003cbr\u003e\n\nFittings must be purchased separately.\u003cbr\u003e\u003cbr\u003e\nIncluded:\u003cbr\u003e\n-Black Anodized Aluminum Fuel Rail\u003cbr\u003e0\n-Black Anodized Aluminum 30mm Injector Seats (20-0160-04)\u003cbr\u003e\n-3x Stainless Steel Mounting Brackets\u003cbr\u003e\n-6x Stainless Steel Mounting Bolts\u003cbr\u003e\u003c!--split--\u003e\u003cstrong\u003eTaxes:\u003c\/strong\u003e\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eSingapore and Malaysia: \u003c\/strong\u003eAll import taxes are included in our pricing.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eEuropean Tva, Iva: \u003c\/strong\u003eTaxes will be calculated during checkout at our company import rate. No additional charges will be added by your local authority.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eUSA:\u003c\/strong\u003e If this product is shipped from our US warehouse then taxes are included. Otherwise, please refer to the rest of the world paragragh.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eRest of the World:\u003c\/strong\u003e Other countries may have to pay their local import tax depending on your country's regulations.\u003chr\u003e\u003cstrong\u003eShipping: \u003c\/strong\u003e\u003cbr\u003e\u003cbr\u003eThis product will be shipped from our US Warehouse to any global location. Shipping via DHL within 3 to 7 days depending on location and local custom check. Allow two additional days for order processing.\u003cbr\u003eEvery Monday our team keeps you in the loop by sending out an \"estimated time of arrival\" email.\u003c!--split--\u003eThis part fits:\u003cbr\u003e\u003cbr\u003eSR20DET | 2000cc | DOHC | 16v | TC | I4\u003c!--split--\u003e","published_at":"2021-11-09T16:27:59+08:00","created_at":"2021-11-09T16:28:00+08:00","vendor":"Radium Engineering","type":"Fuel Rail","tags":["fuel-rail","nissan","radium-engineering","sr20det-2000cc-dohc-16v-tc-i4","us1","ws111"],"price":28070,"price_min":28070,"price_max":28070,"available":true,"price_varies":false,"compare_at_price":29700,"compare_at_price_min":29700,"compare_at_price_max":29700,"compare_at_price_varies":false,"variants":[{"id":40848330358966,"title":"Default Title","option1":"Default Title","option2":null,"option3":null,"sku":"20-0558","requires_shipping":true,"taxable":true,"featured_image":null,"available":true,"name":"Radium Engineering Nissan Silvia SR20DET Fuel Rail Kit - S13","public_title":null,"options":["Default Title"],"price":28070,"weight":2043,"compare_at_price":29700,"inventory_quantity":44,"inventory_management":"shopify","inventory_policy":"deny","barcode":null,"requires_selling_plan":false,"selling_plan_allocations":[]}],"images":["\/\/rzcrewgarage.com\/cdn\/shop\/products\/20-0558.jpg?v=1710247462"],"featured_image":"\/\/rzcrewgarage.com\/cdn\/shop\/products\/20-0558.jpg?v=1710247462","options":["Title"],"media":[{"alt":"Radium Engineering Nissan Silvia SR20DET Fuel Rail Kit - S13-20-0558","id":22867771850934,"position":1,"preview_image":{"aspect_ratio":1.5,"height":400,"width":600,"src":"\/\/rzcrewgarage.com\/cdn\/shop\/products\/20-0558.jpg?v=1710247462"},"aspect_ratio":1.5,"height":400,"media_type":"image","src":"\/\/rzcrewgarage.com\/cdn\/shop\/products\/20-0558.jpg?v=1710247462","width":600}],"requires_selling_plan":false,"selling_plan_groups":[],"content":"\u003cstrong\u003eSpecifications:\u003c\/strong\u003e\u003cbr\u003eManufacturer: Radium Engineering\u003cbr\u003eReference Number: 20-0558\u003cbr\u003e\u003cbr\u003e\u003cbr\u003e\u003cbr\u003eThis CNC machined fuel rail for the Nissan SR20DET features a large 0.69 inch internal bore and high flow ports that accept a wide variety of adapter fittings to suit any custom installation. The black satin anodized finish makes it safe to use with all blends of gasoline and alcohol fuels. It installs to the factory fuel rail mounting points and uses aftermarket top-feed fuel injectors.This fuel rail features an extra 8AN ORB port in the center on the bottom. This can be used as a location for a Radium FPD-R fuel pulse damper (P\/N 20-0176), as shown below. Fuel pulse dampers can be found HERE. Or this port can be plugged.\nThis fuel rail kit is designed for the Nissan S13 SR20DET (RWD configuration) intake manifold.This S13 SR20DET fuel rail will also work on most aftermarket intake manifolds that use the OEM fuel rail (as shown below).\u003cbr\u003e\u003cbr\u003e\nNOTE: there are many aftermarket intake manifolds available for the SR20DET. Radium Engineering has not tested every manifold on the market. Please use the photos on this page to judge if the fuel rail may be compatible. And always ask the intake manifold producer if the OEM fuel rail is compatible. If so, then the Radium fuel rail will likely work as well.Lastly, 3 of the plastic OEM 5mm spacers (Nissan 17522-10V00) must be reused and placed under the included mounting brackets for thermal insulation and proper fuel rail height.The Radium fuel rail converts from side feed fuel injectors to top feed, allowing the use of high flow aftermarket fuel injectors. Fuel injectors are not included and not sold by Radium Engineering. Reference the diagram below to ensure compatible fuel injectors are obtained. For this fuel rail, a 34mm tall universal injector with 14mm upper and lower O-rings must be used. Most popular injector suppliers offer a fuel injector in this configuration. Refer the injector supplier to this page if needed.\nNOTE: Short 34mm injectors are used in this kit because hood clearance may become an issue if taller injectors are used.\u003cbr\u003e\nThe billet aluminum injector seats are anodized and laser etched and press into the intake manifold as shown. They provide a sealed base for the top feed injectors.\u003cbr\u003e\u003cbr\u003e\n\nFittings must be purchased separately.\u003cbr\u003e\u003cbr\u003e\nIncluded:\u003cbr\u003e\n-Black Anodized Aluminum Fuel Rail\u003cbr\u003e0\n-Black Anodized Aluminum 30mm Injector Seats (20-0160-04)\u003cbr\u003e\n-3x Stainless Steel Mounting Brackets\u003cbr\u003e\n-6x Stainless Steel Mounting Bolts\u003cbr\u003e\u003c!--split--\u003e\u003cstrong\u003eTaxes:\u003c\/strong\u003e\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eSingapore and Malaysia: \u003c\/strong\u003eAll import taxes are included in our pricing.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eEuropean Tva, Iva: \u003c\/strong\u003eTaxes will be calculated during checkout at our company import rate. No additional charges will be added by your local authority.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eUSA:\u003c\/strong\u003e If this product is shipped from our US warehouse then taxes are included. Otherwise, please refer to the rest of the world paragragh.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eRest of the World:\u003c\/strong\u003e Other countries may have to pay their local import tax depending on your country's regulations.\u003chr\u003e\u003cstrong\u003eShipping: \u003c\/strong\u003e\u003cbr\u003e\u003cbr\u003eThis product will be shipped from our US Warehouse to any global location. Shipping via DHL within 3 to 7 days depending on location and local custom check. Allow two additional days for order processing.\u003cbr\u003eEvery Monday our team keeps you in the loop by sending out an \"estimated time of arrival\" email.\u003c!--split--\u003eThis part fits:\u003cbr\u003e\u003cbr\u003eSR20DET | 2000cc | DOHC | 16v | TC | I4\u003c!--split--\u003e"}

{"id":7155352567990,"title":"Radium Engineering Nissan S14\/S15 SR20DET Fuel Rail Kit","handle":"radium-engineering-nissan-s14-s15-sr20det-fuel-rail-kit-20-0359","description":"\u003cstrong\u003eSpecifications:\u003c\/strong\u003e\u003cbr\u003eManufacturer: Radium Engineering\u003cbr\u003eReference Number: 20-0359\u003cbr\u003e\u003cbr\u003e\u003cbr\u003e\u003cbr\u003eThis Nissan Silvia fuel rail is specifically designed for the SR20DET S14\/S15 OEM intake manifold.Manufactured with a 0.69\" large internal bore, the fuel rail can support all necessary engine power requirements. The rail is CNC machined from solid 6061 aluminum and black anodized for a high quality surface finish. The included insulating spacers mount the rail to the OEM intake manifold bosses thermal isolation. The Radium fuel rail converts the OEM side feed fuel injector setup to top feed, allowing the use of high flow fuel injectors (not included). The fuel injector bores are 14mm ID. The kit is designed for specific upper and lower O-ring spacing, as depicted.To resist oxidation corrosion, the lower billet aluminum injector seats are anodized and laser etched. They are O-ring sealed and designed for 14mm top feed injectors. This kit is compatible with all fuel types including popular alcohol mixtures such as E85. The OEM 2-bolt IACV bypass hard line is replaced by a billet aluminum IACV spacer kit to gain clearance for the top feed fuel rail. An anodized aluminum barb adapter and rubber hose is supplied to reroute the charge pipe hose externally to the manifold. One gasket is included for the IACV spacer.\u003cbr\u003e\u003cbr\u003eAll parts listed below are included for a trouble and leak-free installation.\u003cbr\u003e\n\n-Black Anodized Aluminum Fuel Rail\u003cbr\u003e\n-Thermal Insulating Spacers (x3)\u003cbr\u003e\n-Thermal Insulating Washers (x3)\u003cbr\u003e\n-Radium 20-0161, Green Anodized Aluminum 25mm Injector Seats (x4)\u003cbr\u003e\n-Radium 20-0162, Black Anodized Aluminum IACV Spacer Kit\u003cbr\u003e\n-Radium 18-0014, IACV Gasket, SR20DET S14\/S15 (x1)\u003cbr\u003e\n-Black Anodized Aluminum IACV Barb Adapter \u003cbr\u003e\n-Rubber Hose and OEM Clamp for IACV\u003cbr\u003e\n-Stainless Steel M8x1.25 Mounting Bolts (x3)\u003cbr\u003e\n-Stainless Steel M6x1 Mounting Bolts (x3)\u003cbr\u003e\u003cbr\u003e\u003c!--split--\u003e\u003cstrong\u003eTaxes:\u003c\/strong\u003e\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eSingapore and Malaysia: \u003c\/strong\u003eAll import taxes are included in our pricing.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eUSA: \u003c\/strong\u003eTaxes are included in this product pricing.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eEuropean Tva, Iva: \u003c\/strong\u003eTaxes will be calculated during checkout at our company import rate. No additional charges will be added by your local authority.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eRest of the World:\u003c\/strong\u003e Other countries may have to pay their local import tax depending on your country's regulations.\u003chr\u003e\u003cstrong\u003eShipping: \u003c\/strong\u003e\u003cbr\u003e\u003cbr\u003eThis product will be shipped from our US Warehouse to any global location. Shipping via DHL\/Fedex within 3 to 7 days depending on location and local custom check. Allow two additional days for order processing.\u003cbr\u003eEvery Monday our team keeps you in the loop by sending out an \"estimated time of arrival\" email.\u003c!--split--\u003eThis part fits:\u003cbr\u003e\u003cbr\u003eSR20DET | 2000cc | DOHC | 16v | TC | I4\u003c!--split--\u003e","published_at":"2021-11-09T16:28:03+08:00","created_at":"2021-11-09T16:28:04+08:00","vendor":"Radium Engineering","type":"Fuel Rail","tags":["fuel-rail","nissan","radium-engineering","sr20det-2000cc-dohc-16v-tc-i4","us1","ws111"],"price":35440,"price_min":35440,"price_max":35440,"available":true,"price_varies":false,"compare_at_price":37500,"compare_at_price_min":37500,"compare_at_price_max":37500,"compare_at_price_varies":false,"variants":[{"id":40848330424502,"title":"Default Title","option1":"Default Title","option2":null,"option3":null,"sku":"20-0359","requires_shipping":true,"taxable":true,"featured_image":null,"available":true,"name":"Radium Engineering Nissan S14\/S15 SR20DET Fuel Rail Kit","public_title":null,"options":["Default Title"],"price":35440,"weight":2451,"compare_at_price":37500,"inventory_quantity":42,"inventory_management":"shopify","inventory_policy":"deny","barcode":null,"requires_selling_plan":false,"selling_plan_allocations":[]}],"images":["\/\/rzcrewgarage.com\/cdn\/shop\/products\/20-0359.jpg?v=1710247465"],"featured_image":"\/\/rzcrewgarage.com\/cdn\/shop\/products\/20-0359.jpg?v=1710247465","options":["Title"],"media":[{"alt":"Radium Engineering Nissan S14\/S15 SR20DET Fuel Rail Kit-20-0359","id":22867773358262,"position":1,"preview_image":{"aspect_ratio":1.5,"height":400,"width":600,"src":"\/\/rzcrewgarage.com\/cdn\/shop\/products\/20-0359.jpg?v=1710247465"},"aspect_ratio":1.5,"height":400,"media_type":"image","src":"\/\/rzcrewgarage.com\/cdn\/shop\/products\/20-0359.jpg?v=1710247465","width":600}],"requires_selling_plan":false,"selling_plan_groups":[],"content":"\u003cstrong\u003eSpecifications:\u003c\/strong\u003e\u003cbr\u003eManufacturer: Radium Engineering\u003cbr\u003eReference Number: 20-0359\u003cbr\u003e\u003cbr\u003e\u003cbr\u003e\u003cbr\u003eThis Nissan Silvia fuel rail is specifically designed for the SR20DET S14\/S15 OEM intake manifold.Manufactured with a 0.69\" large internal bore, the fuel rail can support all necessary engine power requirements. The rail is CNC machined from solid 6061 aluminum and black anodized for a high quality surface finish. The included insulating spacers mount the rail to the OEM intake manifold bosses thermal isolation. The Radium fuel rail converts the OEM side feed fuel injector setup to top feed, allowing the use of high flow fuel injectors (not included). The fuel injector bores are 14mm ID. The kit is designed for specific upper and lower O-ring spacing, as depicted.To resist oxidation corrosion, the lower billet aluminum injector seats are anodized and laser etched. They are O-ring sealed and designed for 14mm top feed injectors. This kit is compatible with all fuel types including popular alcohol mixtures such as E85. The OEM 2-bolt IACV bypass hard line is replaced by a billet aluminum IACV spacer kit to gain clearance for the top feed fuel rail. An anodized aluminum barb adapter and rubber hose is supplied to reroute the charge pipe hose externally to the manifold. One gasket is included for the IACV spacer.\u003cbr\u003e\u003cbr\u003eAll parts listed below are included for a trouble and leak-free installation.\u003cbr\u003e\n\n-Black Anodized Aluminum Fuel Rail\u003cbr\u003e\n-Thermal Insulating Spacers (x3)\u003cbr\u003e\n-Thermal Insulating Washers (x3)\u003cbr\u003e\n-Radium 20-0161, Green Anodized Aluminum 25mm Injector Seats (x4)\u003cbr\u003e\n-Radium 20-0162, Black Anodized Aluminum IACV Spacer Kit\u003cbr\u003e\n-Radium 18-0014, IACV Gasket, SR20DET S14\/S15 (x1)\u003cbr\u003e\n-Black Anodized Aluminum IACV Barb Adapter \u003cbr\u003e\n-Rubber Hose and OEM Clamp for IACV\u003cbr\u003e\n-Stainless Steel M8x1.25 Mounting Bolts (x3)\u003cbr\u003e\n-Stainless Steel M6x1 Mounting Bolts (x3)\u003cbr\u003e\u003cbr\u003e\u003c!--split--\u003e\u003cstrong\u003eTaxes:\u003c\/strong\u003e\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eSingapore and Malaysia: \u003c\/strong\u003eAll import taxes are included in our pricing.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eUSA: \u003c\/strong\u003eTaxes are included in this product pricing.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eEuropean Tva, Iva: \u003c\/strong\u003eTaxes will be calculated during checkout at our company import rate. No additional charges will be added by your local authority.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eRest of the World:\u003c\/strong\u003e Other countries may have to pay their local import tax depending on your country's regulations.\u003chr\u003e\u003cstrong\u003eShipping: \u003c\/strong\u003e\u003cbr\u003e\u003cbr\u003eThis product will be shipped from our US Warehouse to any global location. Shipping via DHL\/Fedex within 3 to 7 days depending on location and local custom check. Allow two additional days for order processing.\u003cbr\u003eEvery Monday our team keeps you in the loop by sending out an \"estimated time of arrival\" email.\u003c!--split--\u003eThis part fits:\u003cbr\u003e\u003cbr\u003eSR20DET | 2000cc | DOHC | 16v | TC | I4\u003c!--split--\u003e"}

{"id":7169324941494,"title":"Radium Engineering Nissan S14\/S15 SR20DET Fuel Rail Kit","handle":"radium-engineering-20-0359","description":"\u003cstrong\u003eSpecifications:\u003c\/strong\u003e\u003cbr\u003eManufacturer: Radium Engineering\u003cbr\u003eReference Number: 20-0359\u003cbr\u003e\u003cbr\u003e\u003cbr\u003e\u003cbr\u003eThis Nissan Silvia fuel rail is specifically designed for the SR20DET S14\/S15 OEM intake manifold.Manufactured with a 0.69\" large internal bore, the fuel rail can support all necessary engine power requirements. The rail is CNC machined from solid 6061 aluminum and black anodized for a high quality surface finish. The included insulating spacers mount the rail to the OEM intake manifold bosses thermal isolation. The Radium fuel rail converts the OEM side feed fuel injector setup to top feed, allowing the use of high flow fuel injectors (not included). The fuel injector bores are 14mm ID. The kit is designed for specific upper and lower O-ring spacing, as depicted.To resist oxidation corrosion, the lower billet aluminum injector seats are anodized and laser etched. They are O-ring sealed and designed for 14mm top feed injectors. This kit is compatible with all fuel types including popular alcohol mixtures such as E85. The OEM 2-bolt IACV bypass hard line is replaced by a billet aluminum IACV spacer kit to gain clearance for the top feed fuel rail. An anodized aluminum barb adapter and rubber hose is supplied to reroute the charge pipe hose externally to the manifold. One gasket is included for the IACV spacer.\u003cbr\u003e\u003cbr\u003eAll parts listed below are included for a trouble and leak-free installation.\u003cbr\u003e\n\n-Black Anodized Aluminum Fuel Rail\u003cbr\u003e\n-Thermal Insulating Spacers (x3)\u003cbr\u003e\n-Thermal Insulating Washers (x3)\u003cbr\u003e\n-Radium 20-0161, Green Anodized Aluminum 25mm Injector Seats (x4)\u003cbr\u003e\n-Radium 20-0162, Black Anodized Aluminum IACV Spacer Kit\u003cbr\u003e\n-Radium 18-0014, IACV Gasket, SR20DET S14\/S15 (x1)\u003cbr\u003e\n-Black Anodized Aluminum IACV Barb Adapter \u003cbr\u003e\n-Rubber Hose and OEM Clamp for IACV\u003cbr\u003e\n-Stainless Steel M8x1.25 Mounting Bolts (x3)\u003cbr\u003e\n-Stainless Steel M6x1 Mounting Bolts (x3)\u003cbr\u003e\u003cbr\u003e\u003c!--split--\u003e\u003cstrong\u003eTaxes:\u003c\/strong\u003e\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eSingapore and Malaysia: \u003c\/strong\u003eAll import taxes are included in our pricing.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eUSA: \u003c\/strong\u003eTaxes are included in this product pricing.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eEuropean Tva, Iva: \u003c\/strong\u003eTaxes will be calculated during checkout at our company import rate. No additional charges will be added by your local authority.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eRest of the World:\u003c\/strong\u003e Other countries may have to pay their local import tax depending on your country's regulations.\u003chr\u003e\u003cstrong\u003eShipping: \u003c\/strong\u003e\u003cbr\u003e\u003cbr\u003eThis product will be shipped from our US Warehouse to any global location. Shipping via DHL\/Fedex within 3 to 7 days depending on location and local custom check. Allow two additional days for order processing.\u003cbr\u003eEvery Monday our team keeps you in the loop by sending out an \"estimated time of arrival\" email.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eImportant:\u003c\/strong\u003e Only 3 left in stock!\u003c!--split--\u003eThis part fits:\u003cbr\u003e\u003cbr\u003eSR20DET | 2000cc | DOHC | 16v | TC | I4\u003c!--split--\u003e","published_at":"2021-11-18T03:10:27+08:00","created_at":"2021-11-18T03:10:28+08:00","vendor":"Radium Engineering","type":"Fuel Rail","tags":["fuel-rail","nissan","radium-engineering","sr20det-2000cc-dohc-16v-tc-i4","us1","ws111"],"price":39510,"price_min":39510,"price_max":39510,"available":true,"price_varies":false,"compare_at_price":38500,"compare_at_price_min":38500,"compare_at_price_max":38500,"compare_at_price_varies":false,"variants":[{"id":40901660246198,"title":"Default Title","option1":"Default Title","option2":null,"option3":null,"sku":"20-0359","requires_shipping":true,"taxable":true,"featured_image":null,"available":true,"name":"Radium Engineering Nissan S14\/S15 SR20DET Fuel Rail Kit","public_title":null,"options":["Default Title"],"price":39510,"weight":5497,"compare_at_price":38500,"inventory_quantity":14,"inventory_management":"shopify","inventory_policy":"deny","barcode":null,"requires_selling_plan":false,"selling_plan_allocations":[]}],"images":["\/\/rzcrewgarage.com\/cdn\/shop\/products\/radium-engineering-nissan-s14s15-sr20det-fuel-rail-kit-rzcrew.jpg?v=1710322172"],"featured_image":"\/\/rzcrewgarage.com\/cdn\/shop\/products\/radium-engineering-nissan-s14s15-sr20det-fuel-rail-kit-rzcrew.jpg?v=1710322172","options":["Title"],"media":[{"alt":"Radium Engineering-20-0359","id":22941871964342,"position":1,"preview_image":{"aspect_ratio":1.5,"height":400,"width":600,"src":"\/\/rzcrewgarage.com\/cdn\/shop\/products\/radium-engineering-nissan-s14s15-sr20det-fuel-rail-kit-rzcrew.jpg?v=1710322172"},"aspect_ratio":1.5,"height":400,"media_type":"image","src":"\/\/rzcrewgarage.com\/cdn\/shop\/products\/radium-engineering-nissan-s14s15-sr20det-fuel-rail-kit-rzcrew.jpg?v=1710322172","width":600}],"requires_selling_plan":false,"selling_plan_groups":[],"content":"\u003cstrong\u003eSpecifications:\u003c\/strong\u003e\u003cbr\u003eManufacturer: Radium Engineering\u003cbr\u003eReference Number: 20-0359\u003cbr\u003e\u003cbr\u003e\u003cbr\u003e\u003cbr\u003eThis Nissan Silvia fuel rail is specifically designed for the SR20DET S14\/S15 OEM intake manifold.Manufactured with a 0.69\" large internal bore, the fuel rail can support all necessary engine power requirements. The rail is CNC machined from solid 6061 aluminum and black anodized for a high quality surface finish. The included insulating spacers mount the rail to the OEM intake manifold bosses thermal isolation. The Radium fuel rail converts the OEM side feed fuel injector setup to top feed, allowing the use of high flow fuel injectors (not included). The fuel injector bores are 14mm ID. The kit is designed for specific upper and lower O-ring spacing, as depicted.To resist oxidation corrosion, the lower billet aluminum injector seats are anodized and laser etched. They are O-ring sealed and designed for 14mm top feed injectors. This kit is compatible with all fuel types including popular alcohol mixtures such as E85. The OEM 2-bolt IACV bypass hard line is replaced by a billet aluminum IACV spacer kit to gain clearance for the top feed fuel rail. An anodized aluminum barb adapter and rubber hose is supplied to reroute the charge pipe hose externally to the manifold. One gasket is included for the IACV spacer.\u003cbr\u003e\u003cbr\u003eAll parts listed below are included for a trouble and leak-free installation.\u003cbr\u003e\n\n-Black Anodized Aluminum Fuel Rail\u003cbr\u003e\n-Thermal Insulating Spacers (x3)\u003cbr\u003e\n-Thermal Insulating Washers (x3)\u003cbr\u003e\n-Radium 20-0161, Green Anodized Aluminum 25mm Injector Seats (x4)\u003cbr\u003e\n-Radium 20-0162, Black Anodized Aluminum IACV Spacer Kit\u003cbr\u003e\n-Radium 18-0014, IACV Gasket, SR20DET S14\/S15 (x1)\u003cbr\u003e\n-Black Anodized Aluminum IACV Barb Adapter \u003cbr\u003e\n-Rubber Hose and OEM Clamp for IACV\u003cbr\u003e\n-Stainless Steel M8x1.25 Mounting Bolts (x3)\u003cbr\u003e\n-Stainless Steel M6x1 Mounting Bolts (x3)\u003cbr\u003e\u003cbr\u003e\u003c!--split--\u003e\u003cstrong\u003eTaxes:\u003c\/strong\u003e\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eSingapore and Malaysia: \u003c\/strong\u003eAll import taxes are included in our pricing.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eUSA: \u003c\/strong\u003eTaxes are included in this product pricing.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eEuropean Tva, Iva: \u003c\/strong\u003eTaxes will be calculated during checkout at our company import rate. No additional charges will be added by your local authority.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eRest of the World:\u003c\/strong\u003e Other countries may have to pay their local import tax depending on your country's regulations.\u003chr\u003e\u003cstrong\u003eShipping: \u003c\/strong\u003e\u003cbr\u003e\u003cbr\u003eThis product will be shipped from our US Warehouse to any global location. Shipping via DHL\/Fedex within 3 to 7 days depending on location and local custom check. Allow two additional days for order processing.\u003cbr\u003eEvery Monday our team keeps you in the loop by sending out an \"estimated time of arrival\" email.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eImportant:\u003c\/strong\u003e Only 3 left in stock!\u003c!--split--\u003eThis part fits:\u003cbr\u003e\u003cbr\u003eSR20DET | 2000cc | DOHC | 16v | TC | I4\u003c!--split--\u003e"}

{"id":7169324908726,"title":"Radium Engineering Nissan Silvia SR20DET Fuel Rail Kit - S13","handle":"radium-engineering-20-0558","description":"\u003cstrong\u003eSpecifications:\u003c\/strong\u003e\u003cbr\u003eManufacturer: Radium Engineering\u003cbr\u003eReference Number: 20-0558\u003cbr\u003e\u003cbr\u003e\u003cbr\u003e\u003cbr\u003eThis CNC machined fuel rail for the Nissan SR20DET features a large 0.69 inch internal bore and high flow ports that accept a wide variety of adapter fittings to suit any custom installation. The black satin anodized finish makes it safe to use with all blends of gasoline and alcohol fuels. It installs to the factory fuel rail mounting points and uses aftermarket top-feed fuel injectors.This fuel rail features an extra 8AN ORB port in the center on the bottom. This can be used as a location for a Radium FPD-R fuel pulse damper (P\/N 20-0176), as shown below. Fuel pulse dampers can be found HERE. Or this port can be plugged.\nThis fuel rail kit is designed for the Nissan S13 SR20DET (RWD configuration) intake manifold.This S13 SR20DET fuel rail will also work on most aftermarket intake manifolds that use the OEM fuel rail (as shown below).\u003cbr\u003e\u003cbr\u003e\nNOTE: there are many aftermarket intake manifolds available for the SR20DET. Radium Engineering has not tested every manifold on the market. Please use the photos on this page to judge if the fuel rail may be compatible. And always ask the intake manifold producer if the OEM fuel rail is compatible. If so, then the Radium fuel rail will likely work as well.Lastly, 3 of the plastic OEM 5mm spacers (Nissan 17522-10V00) must be reused and placed under the included mounting brackets for thermal insulation and proper fuel rail height.The Radium fuel rail converts from side feed fuel injectors to top feed, allowing the use of high flow aftermarket fuel injectors. Fuel injectors are not included and not sold by Radium Engineering. Reference the diagram below to ensure compatible fuel injectors are obtained. For this fuel rail, a 34mm tall universal injector with 14mm upper and lower O-rings must be used. Most popular injector suppliers offer a fuel injector in this configuration. Refer the injector supplier to this page if needed.\nNOTE: Short 34mm injectors are used in this kit because hood clearance may become an issue if taller injectors are used.\u003cbr\u003e\nThe billet aluminum injector seats are anodized and laser etched and press into the intake manifold as shown. They provide a sealed base for the top feed injectors.\u003cbr\u003e\u003cbr\u003e\n\nFittings must be purchased separately.\u003cbr\u003e\u003cbr\u003e\nIncluded:\u003cbr\u003e\n-Black Anodized Aluminum Fuel Rail\u003cbr\u003e0\n-Black Anodized Aluminum 30mm Injector Seats (20-0160-04)\u003cbr\u003e\n-3x Stainless Steel Mounting Brackets\u003cbr\u003e\n-6x Stainless Steel Mounting Bolts\u003cbr\u003e\u003c!--split--\u003e\u003cstrong\u003eTaxes:\u003c\/strong\u003e\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eSingapore and Malaysia: \u003c\/strong\u003eAll import taxes are included in our pricing.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eUSA: \u003c\/strong\u003eTaxes are included in this product pricing.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eEuropean Tva, Iva: \u003c\/strong\u003eTaxes will be calculated during checkout at our company import rate. No additional charges will be added by your local authority.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eRest of the World:\u003c\/strong\u003e Other countries may have to pay their local import tax depending on your country's regulations.\u003chr\u003e\u003cstrong\u003eShipping: \u003c\/strong\u003e\u003cbr\u003e\u003cbr\u003eThis product will be shipped from our US Warehouse to any global location. Shipping via DHL\/Fedex within 3 to 7 days depending on location and local custom check. Allow two additional days for order processing.\u003cbr\u003eEvery Monday our team keeps you in the loop by sending out an \"estimated time of arrival\" email.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eImportant:\u003c\/strong\u003e Only 1 left in stock!\u003c!--split--\u003eThis part fits:\u003cbr\u003e\u003cbr\u003eSR20DET | 2000cc | DOHC | 16v | TC | I4\u003c!--split--\u003e","published_at":"2021-11-18T03:10:26+08:00","created_at":"2021-11-18T03:10:27+08:00","vendor":"Radium Engineering","type":"Fuel Rail","tags":["fuel-rail","nissan","radium-engineering","sr20det-2000cc-dohc-16v-tc-i4","us1","ws110"],"price":31330,"price_min":31330,"price_max":31330,"available":true,"price_varies":false,"compare_at_price":30500,"compare_at_price_min":30500,"compare_at_price_max":30500,"compare_at_price_varies":false,"variants":[{"id":40901660213430,"title":"Default Title","option1":"Default Title","option2":null,"option3":null,"sku":"20-0558","requires_shipping":true,"taxable":true,"featured_image":null,"available":true,"name":"Radium Engineering Nissan Silvia SR20DET Fuel Rail Kit - S13","public_title":null,"options":["Default Title"],"price":31330,"weight":5089,"compare_at_price":30500,"inventory_quantity":17,"inventory_management":"shopify","inventory_policy":"deny","barcode":null,"requires_selling_plan":false,"selling_plan_allocations":[]}],"images":["\/\/rzcrewgarage.com\/cdn\/shop\/products\/radium-engineering-nissan-silvia-sr20det-fuel-rail-kit-s13-rzcrew.jpg?v=1710322174"],"featured_image":"\/\/rzcrewgarage.com\/cdn\/shop\/products\/radium-engineering-nissan-silvia-sr20det-fuel-rail-kit-s13-rzcrew.jpg?v=1710322174","options":["Title"],"media":[{"alt":"Radium Engineering-20-0558","id":22941871407286,"position":1,"preview_image":{"aspect_ratio":1.5,"height":400,"width":600,"src":"\/\/rzcrewgarage.com\/cdn\/shop\/products\/radium-engineering-nissan-silvia-sr20det-fuel-rail-kit-s13-rzcrew.jpg?v=1710322174"},"aspect_ratio":1.5,"height":400,"media_type":"image","src":"\/\/rzcrewgarage.com\/cdn\/shop\/products\/radium-engineering-nissan-silvia-sr20det-fuel-rail-kit-s13-rzcrew.jpg?v=1710322174","width":600}],"requires_selling_plan":false,"selling_plan_groups":[],"content":"\u003cstrong\u003eSpecifications:\u003c\/strong\u003e\u003cbr\u003eManufacturer: Radium Engineering\u003cbr\u003eReference Number: 20-0558\u003cbr\u003e\u003cbr\u003e\u003cbr\u003e\u003cbr\u003eThis CNC machined fuel rail for the Nissan SR20DET features a large 0.69 inch internal bore and high flow ports that accept a wide variety of adapter fittings to suit any custom installation. The black satin anodized finish makes it safe to use with all blends of gasoline and alcohol fuels. It installs to the factory fuel rail mounting points and uses aftermarket top-feed fuel injectors.This fuel rail features an extra 8AN ORB port in the center on the bottom. This can be used as a location for a Radium FPD-R fuel pulse damper (P\/N 20-0176), as shown below. Fuel pulse dampers can be found HERE. Or this port can be plugged.\nThis fuel rail kit is designed for the Nissan S13 SR20DET (RWD configuration) intake manifold.This S13 SR20DET fuel rail will also work on most aftermarket intake manifolds that use the OEM fuel rail (as shown below).\u003cbr\u003e\u003cbr\u003e\nNOTE: there are many aftermarket intake manifolds available for the SR20DET. Radium Engineering has not tested every manifold on the market. Please use the photos on this page to judge if the fuel rail may be compatible. And always ask the intake manifold producer if the OEM fuel rail is compatible. If so, then the Radium fuel rail will likely work as well.Lastly, 3 of the plastic OEM 5mm spacers (Nissan 17522-10V00) must be reused and placed under the included mounting brackets for thermal insulation and proper fuel rail height.The Radium fuel rail converts from side feed fuel injectors to top feed, allowing the use of high flow aftermarket fuel injectors. Fuel injectors are not included and not sold by Radium Engineering. Reference the diagram below to ensure compatible fuel injectors are obtained. For this fuel rail, a 34mm tall universal injector with 14mm upper and lower O-rings must be used. Most popular injector suppliers offer a fuel injector in this configuration. Refer the injector supplier to this page if needed.\nNOTE: Short 34mm injectors are used in this kit because hood clearance may become an issue if taller injectors are used.\u003cbr\u003e\nThe billet aluminum injector seats are anodized and laser etched and press into the intake manifold as shown. They provide a sealed base for the top feed injectors.\u003cbr\u003e\u003cbr\u003e\n\nFittings must be purchased separately.\u003cbr\u003e\u003cbr\u003e\nIncluded:\u003cbr\u003e\n-Black Anodized Aluminum Fuel Rail\u003cbr\u003e0\n-Black Anodized Aluminum 30mm Injector Seats (20-0160-04)\u003cbr\u003e\n-3x Stainless Steel Mounting Brackets\u003cbr\u003e\n-6x Stainless Steel Mounting Bolts\u003cbr\u003e\u003c!--split--\u003e\u003cstrong\u003eTaxes:\u003c\/strong\u003e\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eSingapore and Malaysia: \u003c\/strong\u003eAll import taxes are included in our pricing.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eUSA: \u003c\/strong\u003eTaxes are included in this product pricing.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eEuropean Tva, Iva: \u003c\/strong\u003eTaxes will be calculated during checkout at our company import rate. No additional charges will be added by your local authority.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eRest of the World:\u003c\/strong\u003e Other countries may have to pay their local import tax depending on your country's regulations.\u003chr\u003e\u003cstrong\u003eShipping: \u003c\/strong\u003e\u003cbr\u003e\u003cbr\u003eThis product will be shipped from our US Warehouse to any global location. Shipping via DHL\/Fedex within 3 to 7 days depending on location and local custom check. Allow two additional days for order processing.\u003cbr\u003eEvery Monday our team keeps you in the loop by sending out an \"estimated time of arrival\" email.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eImportant:\u003c\/strong\u003e Only 1 left in stock!\u003c!--split--\u003eThis part fits:\u003cbr\u003e\u003cbr\u003eSR20DET | 2000cc | DOHC | 16v | TC | I4\u003c!--split--\u003e"}